Posts: 2,430
Threads: 134
Likes Received: 211 in 153 posts
Likes Given: 326
Joined: May 2014
I went and picked up some polyester quilt batting sheets to treat my cabs. $20 at the fabric/upholstery store.
Gonna be attempting two things:
1) make my 2x12 less woofy, tighten up the low end and improve the midrange projection.
2) make my 1x10 sound bigger and less thin.
I'm gonna record some before/after samples. Hold on to your butts, this could get interesting!
Posts: 1,089
Threads: 38
Likes Received: 255 in 165 posts
Likes Given: 6
Joined: May 2014
11-06-2014, 04:35 PM
(This post was last modified: 11-06-2014, 04:35 PM by idsnowdog.)
At first I thought the title was and adventure in battling crabs.
Posts: 2,430
Threads: 134
Likes Received: 211 in 153 posts
Likes Given: 326
Joined: May 2014
lol that could be very fun too. probably messy tho. and itchy, if it's THOSE kinda crabs.
Posts: 34,141
Threads: 1,120
Likes Received: 16,583 in 10,874 posts
Likes Given: 2,453
Joined: May 2014
If that fails, you can try ash or alu-mini-mum
Proud Deplorable/Listless Vessel/Garbage!
Posts: 2,430
Threads: 134
Likes Received: 211 in 153 posts
Likes Given: 326
Joined: May 2014
11-06-2014, 08:40 PM
(This post was last modified: 11-06-2014, 08:42 PM by CTN.)
Achievement unlocked: objective #1 completed.
I put a thick layer of batting on the back wall of the cab, and thinner layers on the top and on one side. The bass is considerably tighter, the cab sounds more immediate and lively, the midrange is much clearer and less congested, and the highs jump out much better than they used to. the low end is firm and punchy, but controlled, not bloated like it was before.
see if you can hear it in these clips. I went from medium gain blues rock to 80s cock rock JCM800ish gain to death metal. Each gain level has a before/after and I was playing the same guitar with the same settings on my amp (blackstar HT metal 5), and the same riffs. Used just a room mic to get as close as possible to what I could hear, but overall the recording is a bit brighter and crunchier than what it sounds like in the room. Excuse the shitty playing and ugly fumbles all over the place.
https://soundcloud.com/blakkwater/batting-comparison
Also, for anyone who cares, this was the RCA3 hex-pole JB. Now that the cab is tightened up, I think I actually like the RCA3 just fine in the JB.
Posts: 2,134
Threads: 103
Likes Received: 334 in 233 posts
Likes Given: 164
Joined: Aug 2014
Posts: 2,430
Threads: 134
Likes Received: 211 in 153 posts
Likes Given: 326
Joined: May 2014
does it matter? it's going inside a closed back cab where nobody will see it.
but it's just plain white polyester fiber fill sheets.
Posts: 5,953
Threads: 246
Likes Received: 1,457 in 1,059 posts
Likes Given: 1,507
Joined: May 2014
11-07-2014, 02:00 AM
(This post was last modified: 11-07-2014, 02:02 AM by GoldenVulture.)
That definitely sounds tighter.
Was that a bare inside with sound waves bouncing all over the place, prior to this improvement ?
Padding/Damping is standard stuff in HiFi/Audio speaker boxes. You'll even find it in some PC speakers.
Rockwool is a popular one. Fireproof your cabinet at the same time.
It's probably denser than the polyester and damps even more.
Ha! Check out this. It's a demonstration of Rockwools properties.
-
http://www.rockwool.com/stone+wool+benefits/acoustics -
Posts: 2,430
Threads: 134
Likes Received: 211 in 153 posts
Likes Given: 326
Joined: May 2014
Yup it was just bare birch inside.
I'm gonna work on the 1x10" cab later today. I suspect it's gonna be a bit harder to get it sounding good though, cuz the speaker isn't all that great. Lots of harsh unmusical highs and a boxy, stiff midrange together with thin, undefined bass...
Will report back later.
Posts: 1,176
Threads: 105
Likes Received: 184 in 127 posts
Likes Given: 281
Joined: May 2014
It sounds great dude.
Where was the gain knob at during the death metal section of that demo if you don't mind me asking?